NCP1606BDR2G【PDF 11/22 页】IC POWER FACTOR CONTROLLER 8SOIC

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录45

7页 8页 9页 10页 [11页]12页 13页 14页 15页

NCP1606

http://onsemi.com

When the switch is closed, the inductor current increases

linearly to its peak value. When the switch opens, the

inductor current linearly decreases to zero. At this point,

the drain voltage of the switch (V

) is essentially floating

and begins to drop. If the next switching cycle does not

start, then the voltage will ring with a dampened frequency

around V

. A simple derivation of equations (such as found

in AND8123), leads to the result that good power factor

correction in CRM operation is achieved when the on time

is constant across an ac cycle and is equal to:

2 @ P

OUT

@ L

h @ Vac

RMS

(eq. 1)

A simple plot of this switching over an ac line cycle is

illustrated in Figure 24. The off time varies based on the

instantaneous line voltage, but the on time is kept constant.

This naturally causes the peak inductor current (I

Lpk

) to

follow the ac line voltage.

The NCP1606 represents an ideal method to implement

this constant on time CRM control in a cost effective and

robust solution. The device incorporates an accurate

regulation circuit, a low power startup circuit, and

advanced protection features.

Figure 24. Inductor Waveform During CRM Operation

OFF

MOSFET

(t)

inpk

Lpk

inpk

ERROR AMPLIFIER REGULATION

The NCP1606 is configured to regulate the boost output

voltage based on its built in error amplifier (EA). The error

amplifiers negative terminal is pinned out to FB, the

positive terminal is tied to a 2.5 V ?1.6% reference, and the

output is pinned out to Control (Figure 25).

Figure 25. Error Amplifier and On Time Regulation Circuits

Control

2.5 V

PWM BLOCK

CONTROL

OUT2

OUT1

COMP

PWM

ON(max)

OUT

EAL

EAH

Slope +

CHARGE

CONTROL

A resistor divider from the boost output to the input of the

EA sets the FB level. If the output voltage is too low, then

the FB level will drop and the EA will cause the control

voltage to increase. This increases the on time of the driver,

which increases the power delivered and brings the output

back into regulation. Alternatively, if the output voltage

(and hence FB voltage) is too high, then the control level

decreases and the driver on times are shortened. In this way,

the circuit regulates the output voltage (V

OUT

) so that the

OUT

portion that is applied to FB through the resistor

divider R

OUT1

and R

OUT2

is equal to the internal reference

(2.5 V). The output voltage can then be easily set according

to the following equation:

OUT

+ 2.5 V @

OUT1

) R

OUT2

(eq. 2)

A compensation network is placed between the FB and

Control pins to reduce the speed at which the EA responds

to changes in the boost output. This is necessary due to the

nature of an active PFC circuit. The PFC stage absorbs a

sinusoidal current from a sinusoidal line voltage. Hence,

the converter provides the load with a power that matches

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式